Polyurea Coating Systems Welcomes You

FE-100 Epoxy System

FE-100 is a 100% solids 2 component bisphenol A epoxy system designed as a coating/liner for concrete pipe, manholes and secondary containment applications. FE-100 is provided in a convenient pre-measured two package kit complete with mixing container for ease in field applications. Excellent adhesion to concrete and steel surfaces.
FE-100 provides excellent resistance to sulfuric acid, sodium hydroxide, detergent, bleach and gasoline. PCS-30 primer is recommended to reduce pinhole formations and improve adhesion values.

Typical Applications:	Advantages:
Secondary Containment Sewer Pipe Coating Concrete Coatings	good chemical resistance good wear and impact resistance high build membrane

FE-100 Typical Physical Properties (Neat)

	FE-100A	FE-100B
Solids	12%	12%
Shelf Life	12 mo.	12 mo.	Unopened container stored at 60-100 ⁰F
Flash Point	>250 ^oF		non-flammable
Mix ratio	pre-measured bags

Typical System Performance Characteristics *

Pot Life	45 min (21/2 gallon)	70 ⁰F
Tack free/hard	6-7 hours	75 ⁰F
Bond to Concrete	Concrete Failure	ASTM D-4541
Application Temperature	use at temperatures above 50 ^oF
Color

* values are typical performed under laboratory conditions and may be expected to differ in field applications.

Directions for use:

Surface must be clean and free from contamination. Concrete surfaces must be prepared according to NACE Standard RP0892-92. All surfaces must be free from dust, moisture, oils and contaminates. Concrete must be a minimum of 28 days old. Concrete surfaces must be primed with PCS-30 or PCS-32 according to manufactures instructions. Application of FE-100 must meet manufacturers applications specifications. Please contact PCSI for details.

Carefully open each prepackaged container and add to mix vessel. Mix contents of part A and part B using a Jiffy type mixer until uniform color is achieved.

Application may be made either with a stiff paste brush or steel trowel to a thickness of 65 mils. Work the FE-100 into the surface by applying and finishing in a crosshatch pattern.

Non Skid Coating: To provide non-skid attributes, or a textured finish, apply a base coat of FE-100 to a cleaned and primed surface. Immediately broadcast sand aggregate and allow to dry for 24 hours. After cure, brush off excess aggregate. Apply a 10-20 mil topcoat of FE-100 and allow to cure. Adjust the particle size and amount of aggregate to achieve desired texture.

Safety:

Consult FE-100 A/B MSDS prior to using material. Use proper ventilation and respiratory equipment when applying. Protect skin and eyes from exposure. Follow disposal methods in accordance with local and federal disposal regulations.

Technical Support:

Polyurea Coating Systems maintains a full technical support staff and testing facilities. PCSI also offers on site analysis and consultation for your projects. Please contact PCSI for additional details on how we may tailor your application needs.

Warranty Reference:

The information contained herein is based on data available to Polyurea Coating Systems, Inc. and is believed to be reliable. Since this information, in part, may have been obtained from independent laboratories, or other sources not under our direct supervision, no representation is made that the information is accurate, reliable, complete or representative. We make no guarantee the health and safety precautions Polyurea Coating Systems, Inc. has suggested will be adequate for all individuals and/or situations involving it’s handling and use. Polyurea Coating Systems obligation shall be to replace or pay for any raw material proved defective. Beyond the purchase price of the material supplied by Polyurea Coating Systems, we assume no liability for damages of any kind and the user accepts the products “as is” and without warranties expressed or implied. The suitability of the product for an intended use shall be solely the users responsibility. Users assume all risk and liability whatsoever in connection therewith.

BACK